DuraLay Instructions

Public Channel / Instructions

Share on Social Networks

Share Link

Use permanent link to share in social media

Share with a friend

Please login to send this document by email!

Embed in your website

Select page to start with

Post comment with email address (confirmation of email is required in order to publish comment on website) or please login to post comment

1. For Product Updates & Information, sign up at reliancedental.net/contact/updates Front Back DuraLay Instruction sheet FLAT SIZE: 8.5w x 6.5h FOLDED SIZE 4.25w x 6.5h 4 pages– center fold Gives Sharper Margins Burns Out Cleaner Saves Chair Time CHAIR TIME — Each layer of DuraLay hardens rapidly, so that the initial applications have set by the time the outer layer is applied. Pre-warming powder will accelerate hardening - chilling will slow it. Th e complete operation should take about 5 minutes a ft er handling has become familiar. Seating of fi nished inlays from DuraLay patterns saves considerable chair time. USES OF DURALAY 1. Direct Technique for Cast Posts and Cores 2. Connecting Metal Copings 3. Transfer Copings 4. Connecting a Metal Casting to a Removable Partial Denture 5. Stationary Dies 6. Inlay Impressions 7. Bite Registration COMBINATION KIT : 2 oz. Powder; 2 oz. Liquid; Dropper, Lubricant; Th ree Brushes; Two Dappen Dishes STANDARD PACKAGE : 2 oz. Powder; 2 oz. Liquid; Lubricant; Dropper LABORATORY PACKAGE : 8 oz. Powder; 8 oz. Liquid; Lubricant; Dropper STUDENT KIT : 1 oz. Powder; 1 oz. Liquid; Lubricant; Dropper Reliance Dental Manufacturing, LLC s 5805 W. 117th Place s Alsip, IL 60803 European Representative: Richard L. Milano Via Tiepolo 10126 Torino, Italy

3. For Product Updates & Information, sign up at reliancedental.net/contact/updates Front Back DuraLay Instruction sheet FLAT SIZE: 8.5w x 6.5h FOLDED SIZE 4.25w x 6.5h 4 pages– center fold Gives Sharper Margins Burns Out Cleaner Saves Chair Time CHAIR TIME — Each layer of DuraLay hardens rapidly, so that the initial applications have set by the time the outer layer is applied. Pre-warming powder will accelerate hardening - chilling will slow it. Th e complete operation should take about 5 minutes a ft er handling has become familiar. Seating of fi nished inlays from DuraLay patterns saves considerable chair time. USES OF DURALAY 1. Direct Technique for Cast Posts and Cores 2. Connecting Metal Copings 3. Transfer Copings 4. Connecting a Metal Casting to a Removable Partial Denture 5. Stationary Dies 6. Inlay Impressions 7. Bite Registration COMBINATION KIT : 2 oz. Powder; 2 oz. Liquid; Dropper, Lubricant; Th ree Brushes; Two Dappen Dishes STANDARD PACKAGE : 2 oz. Powder; 2 oz. Liquid; Lubricant; Dropper LABORATORY PACKAGE : 8 oz. Powder; 8 oz. Liquid; Lubricant; Dropper STUDENT KIT : 1 oz. Powder; 1 oz. Liquid; Lubricant; Dropper Reliance Dental Manufacturing, LLC s 5805 W. 117th Place s Alsip, IL 60803 European Representative: Richard L. Milano Via Tiepolo 10126 Torino, Italy

2. For Product Updates & Information, sign up at reliancedental.net/contact/updates Inside Right Inside Left DuraLay Instruction sheet FLAT SIZE: 8.5w x 6.5h FOLDED SIZE 4.25w x 6.5h 4 pages– center fold DIRECT APPLICATION 1. Pour a small portion of DuraLay powder into one dappen dish and about 6 drops of DuraLay liquid into another. 2. Dry cavity of tooth with blast of air and coat with a thin fi lm of DuraLay lubricant to facilitate removal of pattern. Brush o ff excess. 3. Dip small brush in liquid and then into center of powder (do not touch dish) to pick up a bead on tip of brush. Place in base of cavity. If mix is too thick to fl ow into place, dip brush into liquid again and touch it to the mix. 4. A ft er fl oor of cavity is covered, use large brush in same manner to pick up larger quantities and fi ll in remainder of preparation. Flow of DuraLay can be controlled and directed with brush to approximate shape of tooth. 5. When pattern is set (this will take an additional two minutes a ft er last layer is applied), check bite, trim margins and carve as desired, in or out of the mouth, with bur, disk or rubber wheel. 6. For casting, tack on sprue with wax, and invest and burn out in usual manner. Th e DuraLay pattern will volatilize in 40 minutes at 800° F / 427° C leaving no residue. INDIRECT APPLICATION Th e DuraLay Brush Method is equally fast and accurate for building patterns for inlays and bridges on stone, investment or amalgam casts. Rub DuraLay lubricant into model and apply DuraLay beads in same manner as for direct inlays. MATRIX BANDS — On M.O.D.’s, three-quarter crowns and full crowns, a matrix is recommended. Th e matrix will separate easily from the hardened DuraLay. Trim pattern to desired shape, resetting in position to check; then add contact points. PAC K I NG M ET HOD — Make a very thin mix using approximately equal portions of DuraLay powder and liquid by spatulating on a cement slab or stirring in a dappen dish. Th en pack into matrix-contained cavity with instrument. Cover with cellophane or tinfoil and have patient come to occlusion to secure compression. Hold in position until pattern hardens. Remove from tooth; trim to desired shape. USE OF WAX — Contact points and occlusal surfaces may be added with inlay wax a ft er DuraLay base or core has hardened. Wax may be used also for three-quarter and full crowns, linguals, occlusals, and to check margins. UNDERCUTS — If undercuts exist in the preparation, it will be neces - sary to disk or bur through the pattern, remove it, adjust preparation, and reconstruct pattern. HANDLING — As DuraLay liquid evaporates during building process, the resin forms a dense, accurate, non-shrinking pattern that may be trimmed, handled and invested without fear of breakage, chipping, distor - tion or temperature changes. A DuraLay pattern is almost indestructible. PLASTIC TEETH — No separating foil is necessary except when bite is against plastic teeth or fi llings, or when packing method is used. UPPER TEETH — For upper teeth, it is best to place fi rst bead of Dura - Lay in gingival portion of preparation. Enough of it will adhere to gingival section to form a base and permit building of additional layers. The DuraLay Brush Method for Precise Inlay Patterns Moisten brush in liquid. Pick up bead of powder. Deposit powder in preparation. Repeat until preparation is filled. Remove pattern for casting.

Views

  • 1637 Total Views
  • 1207 Website Views
  • 430 Embeded Views

Actions

  • 0 Social Shares
  • 0 Likes
  • 0 Dislikes
  • 0 Comments

Share count

  • 0 Facebook
  • 0 Twitter
  • 0 LinkedIn
  • 0 Google+

Embeds 3

  • 306 www.reliancedental.net
  • 2 translate.googleusercontent.com
  • 1 www.google.is